Hello. Last lesson, you used units to make calculations meaningful. The same care matters when you present measurements: a graph without labelled axes or a readable scale can make good results difficult to understand. This lesson is about turning an experimental results table into a line graph. Allow about 35–40 minutes, including time to draw the worked example on graph paper.
Decide what each axis represents
Suppose you measure the temperature of water at regular times while heating it. You choose when to take each reading; time is the independent variable. The temperature you measure is the dependent variable. Put the independent variable on the horizontal, or , axis and the dependent variable on the vertical, or , axis.
A line graph is useful here because both time and temperature can vary continuously. Each point represents a pair of measurements taken together. Labelling an axis “Time” is not quite enough: Heating time () tells someone whether a reading of 4 means minutes rather than seconds. The other axis needs a quantity and unit too, such as Water temperature ().
Read the short graph-drawing guidance from BBC Bitesize before working through the table below.
Graphs and charts - Working scientifically - KS3 Science - BBC
BBC Bitesize explains where to place the two variables and why axis labels and scales matter.
In “Drawing graphs and charts,” begin with the paragraph about which variable belongs on each axis. Continue through “How to draw graphs and charts,” ending after the paragraph about choosing a scale from the data range and plotting accurately. Read this guidance with those three decisions in mind: axis placement, units, and scale.
Choose scales before plotting
Here is a set of experimental results:
| Heating time () | Water temperature () |
|---|---|
| 0 | 20 |
| 2 | 32 |
| 4 | 44 |
| 6 | 56 |
| 8 | 68 |
| 10 | 80 |
Before drawing axes, find the range each must cover. Time runs from to ; temperature runs from to . A suitable choice on graph paper with at least ten large squares across and eight large squares up is:
- Horizontal axis: to , with each large square representing .
- Vertical axis: to , with each large square representing .
Those scales fit every value, use much of the available space, and are easy to count. Equal distances must represent equal numerical changes along each axis. For example, the marks for , , and must be equally spaced, even though some table readings fall between them.
Starting the temperature axis at zero works well for this example, but it is not compulsory for every graph. If readings occupy a narrow range far from zero, a clearly numbered axis starting near the lowest reading may show their differences better. In either case, never change the size of an interval partway along an axis.
Watch how a worked graph is scaled and plotted. The video also briefly discusses a point that does not match the others; for now, concentrate on its axis and plotting method rather than deciding whether to omit any experimental result.
How to Draw a Graph - WORKED EXAMPLE - GCSE Physics
“How to Draw a Graph – Worked Example” from Physics Online shows scale choices and the placement of points on a real graph.
Watch scaling and plotting, noticing how the presenter checks that the values fit before marking coordinates. Continue through the completed graph to see how the plotted points guide the line and how the axes and points are checked.
Plot each row as one point
Draw the axes with a ruler and number them using the chosen scales. Write Heating time () below the horizontal axis and Water temperature () beside the vertical axis. A useful title is Water temperature during heating.
Now read across the first table row. At , the temperature was , so mark a small cross at . For the next row, move across to , then up to , and mark . On graph paper divided into ten small squares per large square, is two small squares above the line.
Continue in the same way for , , , and . Do not treat the two columns as separate lists: the time and temperature in each row belong to the same cross. Light pencil marks make it easier to correct a misplaced point without obscuring its position.
For these results, the crosses fall along a straight trend. Draw a neat straight line with a ruler through them. Real experimental readings may be scattered slightly; in that case, draw a line or smooth curve that follows the overall pattern rather than forcing a jagged line through every cross. Keep the measured crosses visible so a reader can distinguish results from the line representing their trend.
The kettle graph below shows another temperature-over-time experiment. Notice its named, unit-labelled axes and how its plotted readings follow a curve that levels off, rather than a straight line.
Check the graph against the table
A final check is faster than redrawing a graph later. Read the title and both axis labels: do they state what was measured and in which units? Then scan the numbered marks: does each step of equal size mean the same amount? Finally, count the table rows and the plotted crosses. This table has six rows, so its graph needs six measured points.
Check one cross near each end against its original row, not just against the line you drew. The first should show at ; the last should show at . If a cross looks out of place, check its coordinates before changing the line. A graph should represent the recorded results, not hide a plotting mistake.
Key takeaways
To plot a line graph from a results table, identify the independent and dependent variables, put them on the horizontal and vertical axes respectively, and label both quantities with units. Choose evenly spaced scales that fit the full data range and make good use of the page. Plot one accurate cross for each table row, then draw a line that represents the pattern and check it against the original readings.
This completes the practical calculation and graphing module. Next, you will begin a chemistry refresher by using particle diagrams to distinguish elements, compounds, and mixtures.